What is factory jumper settings?

You may have pins on the back of your hard drive that nothing is connected to. These pins are called jumpers, and are used to enable specific types of settings. You enable particular settings by placing a jumper shunt onto specific pins—creating an electrical circuit between them.

Do I need to set jumpers on a SATA drive?

In the IDE system, most motherboards allow you to have two IDE cables. Each cable can connect to two drives. If you are using SATA drives, you do not need to set jumpers for master and slave because each drive gets its own cable.

What is jumper pin?

Jumper pins (points to be connected by the jumper) are arranged in groups called jumper blocks, each group having at least one pair of contact points. An appropriately sized conductive sleeve called a jumper, or more technically, a shunt jumper, is slipped over the pins to complete the circuit.

Can you clear CMOS without jumper?

If there is no CLR_CMOS jumpers or [CMOS_SW] button on the motherboard, please follow the steps to clear CMOS: Take out the battery gently and put it aside for about 10 minutes or longer. (Or you can use a metal object to connect the two pins in the battery holder to make them short-circuited.)

How can you tell the purpose of a jumper?

In a computer, a jumper is a pair of prongs that are electrical contact points set into the computer motherboard or an adapter card . When you set a jumper, you place a plug on the prongs that completes a contact. In effect, the jumper acts as a switch by closing (or opening) an electrical circuit.

Does it matter what SATA port I use?

Yes, to an extent, it does matter which SATA port you use. However, it also largely depends on the motherboard model and the SATA port version it features. For instance, if you have a recent motherboard model with all the ports being SATA 3, you can use any port to connect your SATA 3 drive.

How do I get my computer to recognize my second hard drive?

Quick Fix for Second Hard Drive Not Detected In Windows 10:

1. Go to Search, type device manager, and press Enter.
2. Expand Disk drives, find the second disk drive, right-click on it, and go to Update driver software.
3. Follow further updates instructions and your hard disk drive will be updated.

Is there a jumper on the optical drive What is the jumper setting?

You may have pins on the back of your hard drive that nothing is connected to. These pins are called jumpers, and are used to enable specific types of settings. The settings these jumpers enable are hard-coded onto a drive’s programmed printed circuit board.

Why is it important to set up the jumper first before installing the hard drive?

For IDE hard drives, it’s important to properly set the jumpers. If not properly done, your computer may not boot or the hard drive won’t be detected. If more than one device is on an IDE port, one device must be set to primary and the other set to secondary or cable select.

How do you use a jumper pin?

To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s) indicated. A jumper is referred to as open or unjumpered when the plug is pushed down over only one pin or if there is no plug at all. When the plug is pushed down over two pins, the jumper is referred to as jumpered.

How do you clear CMOS with a jumper?

Steps to clear CMOS using the jumper method In general, the CMOS jumper is three pins located near the battery. In general, CMOS jumper has positions 1–2 and 2–3. Move the jumper from the default position 1–2 to position 2–3 to clear CMOS. Wait 1–5 minutes then move it back to the default position.

How to set the jumper setting on Samsung hard disk?

Set as Slave: 1 Use this setting if you are installing an additional hard disk drive to a single UDMA cable with a hard disk drive Set… 2 Use this setting if you are installing an additional hard disk drive to a single UDMA cable and the Cable Select setting… More

Do you need to change the jumper setting on Western Digital drives?

Jumper settings will vary, depending on the drive model. There is generally no need to change the default jumper setting in order to use the drive. Your drive’s label will show the exact jumper settings your drive supports. See the images below for examples of our most common jumper settings.

Do you need a jumper on a S-ATA hard drive?

While totally unnecessary in everyday life, jumpers still need fiddling on modern S-ATA drives in some very peculiar, abstract, out of the ordinary (read this as “on an ancient motherboard”) usage scenarios.